Reality Behind
Published

Topology Optimization Delivers Nonintuitive Design Features for Legacy Part (Includes Video)

Refurbishing a legacy turbine engine for energy efficiency provided the opportunity to demonstrate topology optimization in concert with metal 3D printing. The design for this torque arm comes from computer simulation insight refined with a human touch.

Share

The torque arm on the right side of this bell crank assembly for a turbine engine was redesigned using topology optimization and human insight to deliver a final component that both resembles its predecessor and departs from the historic features of this part. Read on or jump to the video below for the full story. Images: Advatech Pacific

Additive manufacturing (AM) has been touted as a production method for legacy components, or replacements for parts that are no longer in production. Design prints or files are often not available for legacy parts, and in the case of molded or cast components, the necessary tooling likely no longer exists. AM can be used in combination with reverse engineering strategies for such parts, making it possible to reproduce them without the original plans or tooling.

But sometimes a faithful reproduction isn’t the goal. Advatech Pacific, an Arizona-based engineering firm, recently worked on a project to update legacy gas turbine engines to be deployed in new markets. 3D printing was selected to help replace legacy parts for these engines not only because the process could quickly produce the small volumes needed without the use of tooling, but also because AM afforded the opportunity to improve the efficiency of the engines. Combining topology optimization with metal 3D printing enabled Advatech to update many of the engine components with designs that use less material and are lighter than their conventional counterparts.

Topology Optimization for Lightweighting

simulated bell crank assembly in ANSYS

The full bell crank assembly for the turbine engine. The torque arm is visible in green, standing nearly vertically just right of center. 

torque arm solid model

The original torque arm model in ANSYS. Extra material was digitally added before performing the optimization to give the algorithm a larger design space to work in.

To demonstrate the benefits of this two-pronged approach, Advatech Pacific Engineering Manager Matt Humrick selected a simple turbine component: a torque arm that connects the engine’s linear actuator to its bell crank. The original arm is a machined stainless steel component about 7 inches long, with interfaces at either end. The solid piece of metal is subjected to a transverse load in use; it requires strength and stiffness, but in its original design it carried more weight than necessary. To optimize this part and reduce its mass, Humrick used ANSYS, a software package that features simulation tools for analysis, design and manufacturing.

The first step was to build a model of the torque arm in ANSYS within its bell crank assembly, with surface contact specified between each part interface, so that the software would have context for the part in use as well as its rough geometry. Faithfully representing the torque arm itself wasn’t necessary, Humrick says; instead, this first model resembles a slightly larger version of the machined part and serves as a guide for the optimization.

“You want to give the software as much freedom as possible,” Humrick says. “One way you can do that is by giving it a larger material envelope to work with.”

Once the model was complete, Humrick set the optimization parameters. In the case of this torque arm, weight reduction was top priority to help the engine operate more efficiently, while maintaining the strength and compliance necessary. He also input the intended material — 17-4 stainless steel, the same as the original part — and set the connecting points as surfaces to preserve. With the constraints in place, Humrick ran the topology optimization to let the software determine where material would be necessary in the final part.  

“Topology optimization is an iterative process,” he explains. “[The software] does a static structural analysis, it looks at your requirements, and then it basically goes in and deletes elements that it doesn't need.” This process repeats until the software reaches a point where removing any additional material would violate the constraints set by the designer.

solved topology optimization for torque arm

Two views of the solved topology optimization for the torque arm, after the ANSYS software removed all the material it deemed unnecessary to meet the load and stress demands on the part. 

The solved model that emerged is an organic shape that represents how the load moves through the torque arm. In contrast to the original human-designed part, the optimized torque arm is not symmetrical. It resembles an I-beam, but with tapered flanges and a central rib that curves. This design feature is the software’s response to information gleaned from simulating the full bell crank assembly: The torque arm is subject to uneven pressure in use.

“You don’t get an even distribution of load through the contact surface,” Humrick explains. “You have a lot of edge contact along the inner edge, and almost no load transfer at all towards the outer end of the shaft.” The software compensated for this load distribution by removing most of the material on the arm’s outer edge and curving the central rib directly toward the inner edge to provide needed support.

Preparing the Topology Optimized Design for 3D Printing

The solved topology optimization model as it stands is not manufacturable. Further design work — with a human touch this time — was needed to develop this model into a printable part. Humrick exported the model into Siemens NX CAD, and used the optimization as the basis for a more refined design. Each CAD iteration was inserted back into the ANSYS bell-crank assembly simulation for validation.

In the final part design, Humrick smoothed the model’s edges and added extra material to the interface surfaces to facilitate machining. He also removed additional material from the curved web by incorporating a truss structure, reducing both support structure material and overall weight.

ANSYS simulation of redesigned torque arm

ANSYS predicted the uneven pressure between the two contact points of the torque arm during the topology optimization process. Humrick’s design, shown here in structural analysis, incorporates this insight into a design with an asymmetric web structure that curves to meet the pressure. 

Further changes were necessary to take the CAD file to a printer-ready file, including selecting the print orientation and incorporating a flat edge on one side of the part to make it easy to print via powder bed fusion and cut from the build plate. The final design incorporates elements of both the simulation-informed topology optimization and human decisions about manufacturability. The 3D printable part matches the stiffness of the original torque arm, but with a 45% weight reduction.

“If you were to optimize this based on hand calculations, you probably end up with a symmetrical I-beam, whereas using the optimization software, you get an I-beam, but with a very unsymmetrical design,” Humrick says. “That was a kind of nonintuitive result that I think highlights the benefits of using topology optimization, not just to minimize the weight of existing designs, but as more of a creative tool.”

3d printed ABS versions of the original and topology optimized torque arm

These half-scale ABS models were 3D printed by Phoenix Analysis & Design Technologies (PADT) to show the difference between the original torque arm and the topology optimized version. The actual replacement part will be 3D printed in 17-4 stainless steel via powder bed fusion. Photo: PADT

I discussed this application in more detail with Humrick and Pam Waterman, 3D printing applications engineer for Phoenix Analysis & Design Technologies (PADT), an ANSYS reseller and frequent collaborator with Advatech. To learn more about the topology optimization process, see the video below:

Related resources: 

AM Workshop
Reality Behind
I Am a Visionary
AM Radio
The Cool Parts Show
AM Workshop

Related Content

Postprocessing

Lightweight Components: A Paradox When Machining

Today’s computer software can just as easily generate lightweight shapes for subtractive processes as it can for additive ones, but it increases cost and waste to make them.

Read More
SPONSORED

Taking the Leap into Additive Manufacturing

SolidCAM’s partnership with Desktop Metal, and its in-depth experience in combined metal 3D printing and CNC finishing, is aimed at making additive manufacturing accessible and profitable for job shops and other manufacturers.

Read More
Design

Additive Manufacturing Production at Scale Reveals the Technology's Next Challenges: AM Radio #28

Seemingly small issues in 3D printing are becoming larger problems that need solutions as manufacturers advance into ongoing production and higher quantities with AM. Stephanie Hendrixson and Peter Zelinski discuss 6 of these challenges on AM Radio. 

Read More
Software

To Scale Additive Manufacturing, Separate Design and Production

Spokbee’s online marketplace is designed to ease the launch and sale of customizable, 3D printed products. Its flexibility comes from cloud-based CAD and a distributed network of service bureaus for production.

Read More

Read Next

Assembly Consolidation

Video: Topology Optimization versus Generative Design

Why do these strategies matter in design for additive manufacturing (DFAM), and what’s the difference? A conversation with PADT’s Eric Miller explores AM and design, including its human element.

Read More
Design

How Topology Optimization Could Be the Key to Longer-Lasting Hip Implants

Hip stem implants must support the mechanical loads of the patient’s lifestyle, but should also avoid stress shielding. A team from Altair leveraged simulation, topology optimization and 3D printing to design an optimized hip stem that meets both conditions.

Read More
Basics

Video: 3 Roles for Simulation in Additive Manufacturing

This conversation with PADT’s Eric Miller explores how simulation and 3D printing work together at three distinct stages in additive manufacturing, for DFAM and beyond.  

Read More
Reality Behind