Aitrtech
Published

Laser Cutting Specialist Develops Large-Travel Additive Approach

For SLM of parts that are multiple feet long, this machine’s build chamber travels throughout the machine area to 3D print the solid part one section at a time.

Share

Of the various limiting factors affecting powder-bed additive manufacturing processes such as selective laser melting (SLM), this one is perhaps the most limiting of all: the build size. Big metal parts can be made additively through metal deposition—a coarse process—but the powder-bed metal AM machines that are capable of fine detail often have build envelopes less than one foot square. Large-travel machines might extend this up to about 16 inches square. Any part much longer than this seemingly is not a candidate for being 3D printed in one piece through a powder-bed process.

And yet, the part seen in the photo above was indeed built in one piece through SLM. This 316L stainless steel part is 900 mm long, or just under 3 feet.

The part was made on an SLM machine developed by machine tool builder Adira, based in Vila Nova de Gaia, Portugal. The innovation that makes big parts practical on this machine is a mobile chamber moving across the powder bed so that the large piece can be built in sections. One other interesting detail about the machine that made this part is that it combines both powder-bed and metal-deposition AM into the same platform.

“Three years ago, we saw we needed to get into AM,” says Filipe Coutinho, company product development engineer. More specifically, the company knew it wanted to provide AM for large metal parts—an industrial demand obvious to this company that seemed underserved. As a maker of laser machines for sheet-metal cutting, the company already had expertise with lasers, and was already oriented toward using those lasers across large-travel machines. It set about developing both metal-deposition and powder-bed machines, both of which it is now bringing to market.

With the metal deposition system it developed, the company recognized that a typical use is likely to be building additive features onto existing large workpieces. Adira therefore focused on allowing an easy transition between laser cutting and laser deposition of material. The system the company developed requires a manual change between these operations, but the change is “very fast,” Coutinho says. “You affix the cladding nozzle and center it—that’s it.” The company’s additive machine offering this system therefore could spend much of its time running as a straightforward metalcutting machine until the additive capability is needed.

By contrast, the large-travel SLM system developed by Adira is much more novel relative to other additive machines. One of the challenges of getting to large travels with a powder-bed machine is controlling the environment across such a large volume. Adira accomplished this with a smaller-volume chamber—just under one foot square—that travels the entire machine area and descends onto the powder from above to contain one section of material at a time. Building the sample part shown took about 80 hours, and the chamber was repeatedly in motion all throughout this time. The following video shows the machine movement, with the chamber advancing from section to section with each single build layer of the part:

Adira recently introduced its new additive offerings using a single machine at the Euroblech trade show in Germany, a machine employing both of these additive capabilities. Marrying metal deposition with SLM in one machine was as much a matter of marketing as engineering, Coutinho says; putting both capabilities in one machine created an impressive showcase for the additive introduction. In general, though, users will want either one capability or the other—either deposition or SLM.

Except: Some users might want both, he says. Manufacturing research facilities are an example. With the demonstration machine, Adira has shown it can combine the capabilities, and in testing it has even succeeded in using them together. Laser deposition can add features onto an SLM part (though the reverse is not possible).

Development still continues, he says. There is much yet to do—significant opportunity exists for further advances, particularly on the powder-bed machine. “We're looking at ways to bring more power to the process, to obtain larger controlled spot sizes for higher build rates,” Coutinho says. For large-size parts on a powder-bed machine, enabling the large build is just the start. “For the next stage, to do large parts more cost-effectively, we are going to need more speed.”

Reality Behind
AM Workshop
I Am a Visionary
AM Radio
AM Workshop
The Cool Parts Show

Related Content

World’s Largest Metal 3D Printer Seen at Ingersoll Grand Opening Event

Maker of large additive and subtractive machines adds capacity in Rockford, Illinois.

Read More
Repair

Hybrid Additive Manufacturing Machine Tools Continue to Make Gains (Includes Video)

The hybrid machine tool is an idea that continues to advance. Two important developments of recent years expand the possibilities for this platform.

Read More
Production

Nicolet Plastics Succeeds Using Mantle's Hybrid Metal 3D Printing Method for Mold Tooling

A recent webinar explores Nicolet Plastics’ success using Trueshape Technology, Mantle’s approach to print injection mold tooling. The current challenges this technology addresses and alleviates in additive manufacturing confirms this method is effectively reducing lead times and cost constraints, while producing better inserts.  

Read More
Software

The World’s Tallest Freestanding 3D Printed Structure

Dimensional Innovations paired additive and subtractive manufacturing to create a monument for the NFL’s Las Vegas Raiders new stadium. The “never been done before” project resulted in the world’s tallest freestanding 3D printed structure.

Read More

Read Next

Defense

At General Atomics, Do Unmanned Aerial Systems Reveal the Future of Aircraft Manufacturing?

The maker of the Predator and SkyGuardian remote aircraft can implement additive manufacturing more rapidly and widely than the makers of other types of planes. The role of 3D printing in current and future UAS components hints at how far AM can go to save cost and time in aircraft production and design.

Read More
FFF

3D Printing Brings Sustainability, Accessibility to Glass Manufacturing

Australian startup Maple Glass Printing has developed a process for extruding glass into artwork, lab implements and architectural elements. Along the way, the company has also found more efficient ways of recycling this material.

Read More
Hybrid manufacturing

Hybrid Additive Manufacturing Machine Tools Continue to Make Gains (Includes Video)

The hybrid machine tool is an idea that continues to advance. Two important developments of recent years expand the possibilities for this platform.

Read More
Airtech International Inc.